Knowledge Base

Everything you need to understand plasma technology all in one place.

Knowledge Articles

Cirrus Plasma System – The effect of surface treatments on interfacial bonding

Researchers from the School of Engineering at the University of Edinburgh have recently published an article that included surface treatments on interfacial bonding using the Henniker Cirrus Atmospheric Plasma System.

The results displayed a significant improvement in the alloys surface wettability and hydrophilic properties.

The work and results are summarised below.
(cited from the Materials and Design publication. [1])

Novel thermoplastic fibre-metal laminates manufactured by vacuum resin infusion: The effect of surface treatments on interfacial bonding.

henniker plasma products atmospheric plasma torch

Fig 1: Henniker's Cirrus atmospheric plasma treatment system mode nozzle


In the paper, Resin-infused thermoplastic fibre-metal laminates (TP-FML) have been manufactured and the bond strength between the metal and composite was tested. The wettability, topography and chemical composition of the treated Al alloy sheets were studied by employing contact-angle goniometry, coherence scanning interferometry, profilometry and X-ray photoelectron spectroscopy.


Prior to surface treatments, the Al alloy sheets were acetone-wiped with lint-free tissues to degrease the surface and afterwards they were subjected to four different surface treatments; alkaline etching, acid treatment, electrochemical etching and an atmospheric plasma treatment using a Henniker Cirrus system.

henniker plasma models cirrus home page

Fig 2: Henniker's Cirrus atmospheric plasma treatment system


Surface wettability:

One pass of the atmospheric plasma nozzle at 1mm/s decreased the contact angle from 82 ± 1° to 32 ± 2.5°. This also increased the surface energy from 34.3mJ/m2 to 63.5mJ/m2. The atmospheric plasma treatment showed the most improved contact angle and surface energy measurements out of all four treatments used, with the next best being the acid etching decreasing contact angle to 37 ± 3°  and increasing surface energy 61.05mJ/m2.

“The plasma-treated Al alloy surface exhibited a significant improvement in the surface wettability due to increased surface polarity. The oxidation of the surface and the removal of the carbonaceous components made the Al surface more hydrophilic.”  [2]

Chemical Composition:

The X-ray photoelectron spectroscopy (XPS) method was adopted to determine the chemical composition on the surface of the treated Al alloy samples. The atomic fraction of carbon on the surface of the degreased-only Al alloy sample was ~72%, which was reduced to 48% after atmospheric plasma treatment.

Keywords; Fibre-metal laminates, Thermoplastic matrix, Surface treatments, Interface bonding, Mechanical properties



See what our customers have to say

  • "The technical team at Henniker are very knowledgeable and supportive and always approachable. I have found it a pleasure to work with them."

    Simon Baxter - BAE Systems, MAI

  • "Henniker guided us to choose the most suitable plasma unit for our application, ensured an accelerated delivery time & guided us through the very easy setup. We obtained quality results with their unit within minutes of setup & consistent results thereafter. The support they have provided has been rapid and helpful."

    Dr Ravi Desai - Making Lab, Francis Crick Institute

    Francis Crick Institute
  • "Henniker provided our team with excellent service during the course of our work together, the plasma cleaner arrived quickly and was installed with ease, giving us visible results from the outset and confirming that we made the right decision in choosing a local UK manufacturer."

    Dr Panagiotis Manesiotis BSc MRSC - Queen’s University Belfast

    Queens Uni Belfast
  • "Our customers and operations demand reliability at every level and were a key factor in our decision to choose a UK based manufacturer of plasma treatment equipment."

    Tom Doak - Trak Microwave

    Queens Uni Belfast
  • "Henniker’s after sales support is first class. They have always been extremely responsive if we have ever had need to call on them."

    Steve Rackham - Teledyne

  • "Henniker’s plasma systems have delivered tangible benefits to us right from day one. The team there are very easy to work with."

    Ian Bruce - Coopervision

  • "Henniker really stood out, both in their product range and technical knowledge. They are a great company to work with."

    Karthik Nair - University of Bradford

    University of Bradford
  • "We are very impressed with the ease of use and reliability of our plasma unit and were producing results within minutes of setting it up."

    Dr Neil Wilson - Warwick University

    Warwick University
  • "Our collaborative work with the team at Henniker was a very positive experience and one that we look forward to developing further."

    Ewen Kellar - TWI

  • "Henniker provided a tailored product to match our exact requirements. They are a pleasure to work with."

    Dr Will Shu - Heriot Watt University

    Heriot Watt University

  • Huf
  • Kingspan
  • BOC
  • Maclaren
  • Cambridge Uni
  • Warwick Uni
  • Morgan Ceramics
  • QMUL
  • University Bradford
  • BAE
  • Imperial College London
  • Heriot Watt Uni
Henniker Plasma Logo

ISO logo



Connect with us

Henniker Plasma 3 Berkeley Court, Manor Park, Runcorn, WA7 1TQ, UK

  +44 (0)1925 830 771     +44 (0)1925 800 035